Minka Lavery 4933-284 Instruction Manual download pdf

INSTALLATION INSTRUCTION FOR FIXTURE #4933

ASSEMBLING THE FIXTURE (FIG. 1)

1. Shut off the power at the fuse box or circuit breaker. If

necessary, remove the old fixture including the mounting

hardware.

2. Carefully remove the old fixture from the carton and check that

all parts are included as shown in the illustration.

3. Thread the fixture loop (A) tightly onto the nipple (B).

4. Adjust the fixture arms to the proper position.

5. Place the glass shade (E) over the socket (F), then secure with

the cushion ring (D) and socket ring (C).

6. Install the light bulb in accordance with fixture’s specifications.

(DO NOT EXCEED THE MAXIMUM WATTAGE RATING!) (NE

PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE!).

MOUNTING THE FIXTURE (FIG. 2)

1. Thread the nipple (S) into the collar loop (T) until snug.

2. Thread the other end of nipple (S) into cross bar (P) until snug.

The side of the cross bar marked with “GND” must face out.

3. Place lock washer (Q) over the end of nipple (S) protruding

through cross bar (P) and thread hex nut (R) onto nipple (S) until

tight.

4. Take this crossbar assembly and mount to ceiling outlet box (V)

tightly using outlet box screws (W).

5. Use proper chain pliers to open one end link of the chain and

connect to the fixture loop (A). Close the link.

6. By measuring, determine correct number of links needed for

proper hanging height. Using a pair of chain pliers, disconnect

and discard the remaining chain.

7. Lace the fixture wires through the chain (X).

8. Slip collar ring (Y) over the chain (X), then do the same with

canopy (U).

9. Open the other end link of the chain (X) and connect to the collar

loop (T). Close the link.

10. Feed the fixture wires through the collar loop (T) and nipple (S)

and pull until tight.

CONNECTING THE WIRES (WIRING DIAGRAM)

11. At this point, connect the electrical wire as shown in the wiring

illustration, making sure that all wire connectors are secured. If

your outlet has a ground wire (green or bare copper), connect

the fixtures ground wire to it. Otherwise, connect the fixture

ground wire directly to the crossbar using the Green Screw

provided.

12. Tuck these wires connectors neatly into the ceiling out let box

and raise the collar ring (Y) and thread onto collar loop (T)

protruding through canopy.

Your installation is now complete. Return power to the junction box

and test the fixture.

Notice: It is important to use proper chain pliers (not

included) to OPEN and CLOSE the chain included with

this fixture. Do not open them with other tools that may

twist or stress the chain links. It is important to use

proper chain pliers like the ones shown in the diagram.

GLASS SHADE(E)

SOCKET(F)

LOOP(A)

NIPPLE(B)

FIXTURE

BODY

Fig. 1

Fig. 2

WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.

AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.

(SKT-RING-26)

Set A#A-010

-Crossbar

-Ground Screw

-Mounting screws (2)

Chain # HCH3072-281

Gauge 4.5MM

Summary of Contents

Page 1

INSTALLATION INSTRUCTION FOR FIXTURE #4933ASSEMBLING THE FIXTURE (FIG. 1)1. Shut off the power at the fuse box or circuit breaker. Ifnecessary, remove

Comments to this Manuals

No comments

Minka Lavery 4933-284 Instruction Manual

Browse online or download Instruction Manual for Unknown Minka Lavery 4933-284. Minka Lavery 4933-284 Instructions / Assembly User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Unknown Minka Lavery 4933-284