INSTALLATION INSTRUCTIONS
For Model #664-PL,666-PL,668-PL
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.
CAUTION
Turn off the main power at the circuit breaker before
installing the fixture, in order to prevent possible shock.
GENERAL
All electrical connections must be in accordance with
local unfamiliar with proper electrical wiring connections
obtain the services of a qualified electrician.
Remove the fixture and the mounting package from the
box and make sure that no parts are missing by
referencing the illustrations on the installation instruction.
ASSEMBLY AND INSTALLATION
1. Turn off the power.
2. Remove the NUTS(19)from one of the END CAP
(18).Then take the End Cap out and pull the Acrylic
Lens(21) out from the other end of End Cap(18).
3. Pull the SUPPLY WIRES (2) & (4) and HOUSE
GROUND WIRE (3) out from the OUTLET BOX (1).
4. Loosen the 2 COPPER NUTS(15) on the FIXTURE
BODY(14).Then take the BACK PANEL(10)out from
the FIXTURE BODY(14).
5. Position the BACK PANEL(10) over the OUTLET
BOX (1). Mark the location of the two KEYHOLE
SLOTS located on the BACK PANEL(10). Be sure to
mark only the narrow part of the KEYHOLE SLOTS.
Remove the BACK PANEL(10) from the ceiling. Drill
the two holes using the appropriately sized drill bit.
Insert the provided Ceiling ANCHORS (9) into the
holes.
6. Put all the fixture wires through BACK PANEL (10).
7. Make the wiring connections: connect the WHITE
SUPPLY WIRE(2) to the WHITE FIXTURE WIRE(5);
connect the BLACK SUPPLY WIRE(4) to the BLACK
FIXTURE WIRE(7);connect the HOUSE GROUND
WIRE (3)to the FIXTURE GROUND WIRE (6)using
WIRE CONNECTOR(8) (PROVIDED). Carefully tuck
all wires back into the OUTLET BOX (1) (See Fig.2)
8. Locate the BACK PANEL (10) over the OUTLET BOX
(1), put the MOUNTING SCREWS (13) through the
slots on the back panel. Then secure the MOUNTING
SCREWS(13) to the OUTLET BOX(1)tightly. Secure
the ANCHOR SCREWS (12) to the ANCHORS(9)
9. Put the FIXTURE BODY(14) over the BACK PANEL(10)
through the two SCREWS(11) and secure it by 2
COPPER NUTS (15).
10. Now you are ready to install the LAMP(20). Do not
exceed recommended maximum wattage.
11. Insert the ACRYLIC LENS (21) to one end of the End
Cap. Then put the other end cap through the
SCREWS(17) and secured by the NUTS(19).
INSTALLATION IS NOW COMPLETED
Fig.1
Fig. 2
1. OUTLET BOX
2.WHITE SUPPLY WIRE
3.HOUSE GROUND WIRE
4.BLACK SUPPLY WIRE
5.WHITE FIXTURE WIRE
6.FIXTURE GROUND WIRE
7.BLACK FIXTURE WIRE
8.WIRE CONNECTOR
9.ANCHOR
10.BACK PANEL
11.SCREW
12.ANCHOR SCREW
13.MOUNTING SCREW
14.FIXTURE BODY
15.COPPER NUT
16.SOCKET
17.SCREW
18.END CAP
19.NUT
20.LAMP
21.ACRYLIC LENS
WIRES
Black or
Smooth
WIRES
Black
(Hot)
WIRES
White or
Ribbed
WIRES
White
(Neutral)
WIRES
Bare
Copper
(Ground)
WIRES
Green
(Ground)
PDF created with pdfFactory Pro trial version www.pdffactory.com
(1 pages)
(1 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals